ASUS ROG Zenith Extreme X399 Motherboard Review


Hey guys, Jarrod here and today we’re going
to check out the ASUS ROG Zenith Extreme X399 motherboard. This is a Threadripper board
which I’m using in my new PC, I’ll cover what’s on offer as well as the problems
I’ve had with it so far that you should be aware of before buying. Inside the box there’s quite a lot of components,
starting with the motherboard itself. Under that there’s a box that’s full of extra
items, including a brace for the graphics card, a 10gbit network card, the DIMM expansion
card, SLI bridges for two, three, and four way SLI configurations, a fan hub, two antennas
for the wifi, and a USB stick containing drivers as well as heaps of additional cables for
just about everything. This is an E-ATX board, it’s 30.5cm by 27.7cm
and I’ve installed it into my Thermaltake View 71 case. Let’s start by take a closer look at the
rear IO. The IO shield is attached to the board, so no need to install that first. From
left to right, we’ve got BIOS flashback and clear CMOS buttons. Next there are three
connectors for the included WiFi antenna. After that there are 8 USB 3.1 Gen 1 Type
A ports which are colored blue, and a built in gigabit ethernet port. There’s two USB
3.1 Gen 2 ports, one is Type A and coloured red, while the other is a type C port, as
well as an optical SPDIF out, and your usual audio outputs which light up with LEDs. Now let’s checkout the rest of the board.
Along the top from left to right there’s a water block connector, RGB header, and in
the top right corner there’s a CPU fan and CPU opt header. Working down from here along
the right hand side of the board there’s two 8 pin power connectors, physical power
on and reset buttons which were nice to have while troubleshooting, 24 pin power connector,
and a USB 3.1 gen 2 header with another fan header behind that. The rest of the IO on the right faces out
to the side, we’ve got the USB 3.1 gen 1 header, 6 SATA3 connectors, and one U.2 output. Along the bottom from right to left there’s
the usual front panel connectors, various pump connectors for water cooling, LN2 jumpers
for liquid nitrogen support, buttons for safe boot, more fan headers, another USB 3.1 gen
1 connector, USB 2.0 connector, addressable RGB header and Aura RGB header, TPM connector,
EZ power plug if you’re running heaps of GPUs, and front panel audio connectors, so
there’s quite a lot going on. Of course in the center of the board we’ve
got the TR4 socket, which I’m using for my 16 core AMD 1950X CPU. I had a lot of trouble
getting the CPU installed, as you may have heard the Foxconn sockets don’t seem to
be as good as the Lotes ones. You’re meant to tighten the screws in the order specified,
however I had to half turn screws 2 and 3 first, then put my full body weight behind
1 to get it to thread, and I’m not alone with this issue. I eventually got it in, but
I was pretty worried I was going to damage the board just installing it, hopefully this
will be fixed in future revisions. The socket is surrounded by the 8 memory slots
which run in quad channel that support up to 128GB of DDR4 memory at 2,666MHz with the
possibility of overclocking to 3,600MHz. I had difficulty getting above 3,000MHz using
my G.Skill TridentZ kit, but that wasn’t on the supported parts list, so if you plan
on overclocking make sure you pick supported memory from the QVL as AMD’s platforms seem
to be fairly picky with memory. You also have the option of using ECC memory here, a nice
touch if you’re running a Threadripper workstation or server. Towards the right of the memory slots is the
expansion DIMM.2 slot. This is an interesting feature, basically you can connect the included
add in card into what is essentially another DDR4 interface slot in order to run up to
two M.2 drives. These can be 30mm, 42mm, 60mm, 80mm or 110mm in length. I haven’t been
using this yet, as there’s also a single M.2 PCIe slot under the metal plate with the
ROG logo. This panel also acts as a heatsink for the x399 chipset, and it’s got a thermal
pad underneath which comes into contact with the M.2 drive. There’s support here for
M.2 drives 42mm, 60mm or 80mm in length. The RGB lighting also shines through the ROG logo
cutout. As for available PCIe slots from the top down
there’s PCIe 3 16, 8, 4, 16, 1, and 8 slots. This supports up to either 4 way SLI or Crossfire.
The top 16x slot is closer to the CPU socket than other X399 motherboards, so check your
CPU cooler won’t overhang the slot like mine does. I’ve got the Noctua U14S cooler,
and it blocks out this first slot, preventing me from using it. That’s not an issue for
me, as I’m only running one graphics card in the second 16x slot, but if I want to use
both of these in future I’ll need to look at changing the CPU cooler to something smaller. Speaking of PCIe slots, the included 10 gigabit
network card will let you boost your network speed as long as your network supports such
speeds. It connects using a PCIe 3.0 4x interface, and I ended up putting mine into the otherwise
unusable top x16 slot. It’s covered in a heat sink to help cool it, and has some LEDs
on top which advise the speed connection. If you have no use for this card I’d probably
recommend looking at a different X399 motherboard, as the card itself costs around $140 USD,
so it would be adding significant cost to the overall price of the board. I’ll be
upgrading my network to 10gbit in the near future, so I’ll definitely be making use
of this. While we’re talking about network connectivity
let’s dive into the WiFi. There are two antenna included with the board, the first
is dual band and connects to two of the connectors on the back of the motherboard. This one handles
802.11 a, b, g, n, and ac standards over 2.4GHz or 5GHz frequencies. The second antenna plugs
into the third connector, and is for 802.11ad, also known as WiGig, which operates on the
60GHz frequency with speeds up to 4.6GBps. Unfortunately I wasn’t able to test this
for myself as I don’t have any devices to take advantage of the ad standard yet. Both
antennas have stands to hold themselves up, and there’s also support for Bluetooth 4.1 As you may have noticed, the board also has
RGB lighting, but I think it looks nice and isn’t overdone. It features ASUS’s Aura
sync, so you can use their software to customize the lighting effects and also synchronize
other components, which is what I’m doing here with my G.Skill memory. The lighting
is present around the right edge of the board, on the metal plate with the ROG logo, and
on the shroud covering the IO. The IO shroud also covers a tiny fan, which
you’ll hear spinning up on system boot. Just under that there’s a small OLED panel
which gives useful system information. I found this really helpful during boot when I had
problems, as it would print out the error code. While running it will show the current
CPU temperature by default, but you can change it to show CPU frequency, fan speed, water
cooling information, or even a custom GIF. On the back of the board there’s a nice
backplate, not that you’ll see it once installed. I had difficulty installing this into my Thermaltake
View 71 case. Although the case does support the E-ATX form factor, the motherboard covers
the cable routing grommets, and the backplate comes into contact with the rubber grommets,
so I had to remove the rubber from the case so that the board would sit flush against
the case. Once getting up and running the board has
worked great, but I did have some issues when building the system as already mentioned,
including the CPU cooler overhanging of the first PCIe slot, difficulty installing the
CPU in the foxconn socket, and backplate coming into contact with some of the case. These
type of issues are only minor, once you work around them you’ll probably be fine for
as long as you continue using the system, I haven’t had any further issues since building
the system a few months ago. While building I also had a few different
issues with the memory being recognized initially, long story short I updated to the latest BIOS
by simply copying the files to a USB stick, inserting it into the BIOS USB port and pressing
the BIOS button. It fixed everything for me, so make sure you’re running the most up
to date version. The BIOS update process was extremely simple to do this way, I was quite
impressed. So what did you guys think about the ASUS
Zenith Extreme motherboard? It’s the most expensive X399 board at the time of recording,
and there are definitely cheaper options out there, however in my personal opinion this
one looks the nicest and has really useful features and add ons, such as the inclusion
of the 10 gigabit network card which I’ll be using. Be sure to let me know your thoughts
down in the comments, as well as what motherboards you’re looking to buy and why? If you found
the information in this video useful leave a like, and don’t forget to subscribe for
future tech videos like this one.

16 thoughts on “ASUS ROG Zenith Extreme X399 Motherboard Review

  1. The DIMM expansion card lets you add two extra M.2 NVMe SSDs. Does it come with a small fan to cool them? If you visit the ASUS website there is a picture showing a small fan mounted on that riser.

    Also, I was planning to use the Enermax LiqTech AiO cooler instead of the Noctua to improve thermals as remove that obstruction of the PCI slot. However no Australian dealer sells it after the wholesaler MWave discontinued distribution.

  2. It is the most expensive, yes. It is one of the most beautiful ones, yes. But, it is also one of the most problematic X399 motherboards on the market! There is also one component on it that is actually defective and ASUS knows that, and are closing their eyes about it! It is ITE IO chip housing the hardware monitor among other things. This HW monitor has an issue and is not reporting the real temperatures and Voltages, also this messes up the fan speed controls and there have been cases of systems overheating as the Water Pump header just stops the pump at random… The same issues are also present on the X370 boards…(with the same model ITE chip)

  3. i own one of this and the only problem i had was with the socket. I had rode something about the foxcomm socket and atm to install the 1950x, i knew that i have to make extra efford to place the scrubs. But once i got the sistem built, and updated bios , everything worked absolutelly flawlesly. I got my t-force nighthack 32 gb kit working with no-issues at 3066 mhz @1.35v, however, i couldnt use the default XPM profile from the memory, i had to manual overclock them.
    as a detalil, well, if you put a wrong configuration on the memory, the bios will not even post and you have to press the clear cmos buttom at the back on the motherboard to restore default and thats very annoying. But at the end of the day, once everything was pluged and configured, the system worked absolutelly fantastic. Great content man, keep the good job.

  4. TOOOOOtally overkill. Now, if I had a 10Gb network, maybe. And if I had a hard-on for RGB, maybe, but I don't.

  5. Interesting review, but please use fewer words and speak more slowly. You sound like you need to catch the next flight…

  6. I've found some problem with this motherboard.

    WiFi Rage is so poor, my router is next to my cabinet and it's showing less signals and significantly low WiFi speed.

    same happens with Bluetooth, If is there any solution please let me know. Thanks

    BTW nice video.

Leave a Reply

Your email address will not be published. Required fields are marked *

Copyright © 2019 Explore Mellieha. All rights reserved.